Products
02-11 zuma led blinker kit
$ 49.99
Clean, cost effective LED blinker kit. These go in place of the yamaha badge. These are CRAZY crisp and bright, much safer and more visible than the oem blinkers. You...
02-11 zuma, jog engine mount bearings
Sold Out
Replacement bearings for your yamaha engine mounts. These replace the two sealed bearings, in the case. Simply uninstall your pin, c clips, and bearings and install new! One kit comes...
1 1/4" handlebars
$ 12.99
1 1/4" handlebars for your 2 wheeled ride. Choose black, red or silver
10mm axle 216mm
$ 15.99
216mm axle, 10mm. Good fit for elite, dio, and more! Measure beforehand to check fitment!
10mm c clip
$ 10.99
Replacement c clips for your bike. These are 10mm, PLEASE verify your bike uses 10mm clips before purchasing. Comes with 2 clips
10mm wheel bearing KIT
$ 14.99
10mm replacement wheel bearing kit for Yamaha zuma (89-11), and other scooters that use a 6300 bearing These bearings measure 10 (ID) x 35 (OD) x 11 (Width) If you are...
10mm wheel bearings
Sold Out
Here's some 10mm wheel bearings for your scooter! Sold individually, so grab 2 for a matching set! Measures 10x35x11mm
112 Link 420 O-Ring Chain
$ 33.99
This 420 x 112L chain is required when putting a larger sprocket on your sur-ron, or talaria bike! 54T Sprocket available here!
12mm Dellorto Carburetor
$ 141.99 $ 142.99
Here's a good stock replacement carburetor for your 1990-2001 prebug zuma! Works with all stock cables just bolt on and go! Will also fit 1999 aprilia sr50, and lots of...
12mm NCY speedo gear
$ 34.99
If you're running 12mm legs on your ruckus, met, or honda dio, and want to use the factory speedo, this is a piece to the puzzle most people forget about....
12mm wrist pin bearing honda yamaha
$ 14.99
Hi, this is a NECESSARY component to replace when doing your top end, crank or general rebuild. These bearings require NO special tools, and work on all 49cc 2 strokes,...
13mm Star washer for minarelli
$ 8.99
Replacement 13mm star washer for minarelli, always good to swap these out if yours has slop on the crank or is worn out!
16x13 Motoforce Roller Set
$ 14.99
Grab yourself some affordable rollers for your scoot. These are what control how fast/slow your trans shifts. PLEASE check your roller size before ordering. Will fit most aftermarket Mina. Variators....
16x22x12 needle bearing
$ 12.00
16x22x12 malossi needle bearing, intended for RC one applications, but may work in other places too!
18x14 GY6 Dr pulley sliders
$ 28.99
Due to requests, I now stock Dr Pulley slider kits. These differ from rollers, as they don't roll in the variator, they slide. These sliding rollers perform better than standard...
18x14 NCY Roller weights CH80
$ 23.99
Brand new 18 x 14 Roller weights for your honda elite CH80!
190mm Brake Rotor
$ 33.99
Replacement brake rotor for your honda, yamaha, or aprilia scooter! Please use the below measurements to make sure this will fit! Outside diameter: 190mm Inner diameter (intake): 58mm Hole diameter:...
1986-1991 yamaha jog variator
$ 66.00
Variator kit for your FIRT gen jog, vertical. 1986-1991. These DO NOT fit the horizontal 92+ models.
1989-2001 Yamaha Zuma Air filter
$ 5.99
OEM Style air filter replacement for 1989-2001 Yamaha zuma!
1989-2001 zuma headlight conversion
Sold Out
aftermarket headlight system for your 89-01 yamaha zuma. Choose from black or white
1990 Zuma II seat, tank, and rack
$ 440.00
Seat, tank, and rack off of a 1990 yamaha zuma, hard to find parts! Seat is in good condition, gas tank is rust free! Includes tail light and turn signals!
19x15.5 Roller Sets
$ 23.99
This is the most common size weight needed for your overrange kit. These are used for the polini, malossi, and stage6 overrange yamaha kits. 19x15.5mm rollers are also used stock...
19x15.5 rollers
$ 19.99
19x15.5 rollers for your compatible variator! Choose from 10 gram or 11 gram!
2 fast 100cc zuma components
$ 823.99
We now offer these parts individually, these are parts you need for 100cc setup, on stock minarelli cases, such as zuma 02-11, sr50 1999, yamaha jog and more. choose...